Integrated Low Heating Brushless Servo Motor with Driver Built-in

Integrated Low Heating Brushless Servo Motor with Driver Built-in

 Integrated Minimal Heating Brushless Servo Motor with Driver Built-in

57IV90/57IV130/57IV180 Characteristics
1.Functioning voltage: DC enter voltage 15VDC to 50VDC ,advise voltage is 36V
2.The max continuous output current is 10A, the max peak recent is 22A (three moments overload capacity) 
3.Satisfactory differential or solitary-ended pulse / route command, have 3 manage mode of place, speed and torqe
four.Using FOC magnetic situation management engineering and area vector pulse width modulation (SVPWM) shut-loop handle technological innovation
five.The variety of pulses per cycle (subdivision) can be established by the debug computer software or the dial switch environment(electronic equipment ratio)
six.Have 3 varieties of 90w,130w and 180w DC brushless servo motor to choose.
seven.Have security of overvoltage, undervoltage, overcurrent and tolerance,and many others.
eight.Solitary / double pulse mode, the pulse legitimate edge can be pick.
nine.The max pulse frequency of management instruction is 500KHz (factory default is 200KHz)
10.Pulse, route and allow signal enter interface level is 4.five to 28V compatible
11.With serial RS232 / RS485 debugging operate, but need to have to use our special serial debugging cable 
12.Performance: sleek velocity, little overshoot ,modest monitoring mistake, lower heat of motor and driver

Advantage
This servo motor method is created up of brushless servo motor with driver developed-in.Compact and little size is ideal for some spot that has prerequisite of volume.It has much less wiring to decrease mistakes,keep secure and simple for installation.This built-in servo program has excellent pace adjustment performance,massive commencing torque,easy procedure, high rotating speed.The value is significantly reduced than AC servo motor, but some performances are greater than AC servo goods.

Driver Model And Variety Xihu (West Lake) Dis.

Motor Type  57IV90 57IV130 57IV180
Rated power(W) 90W 130W 180W
Vector Maximum Current 16A 18A 22A
Body Length(MM) 106.2 0.five 126.2 0.5 146.2 0.five
Operation Voltage 15-50Vdc,36Vdc recommend 
Overvoltage Protection Voltage 68Vdc±2
Control Method 32 bits DSP vector FOC control technology
Pulse Limit Frequency 500KHz(factory default 200KHz)
Safety Overcurrent, overvoltage, undervoltage and tracking error tolerance alarm
Input Signal  Pulse, direction and enable differential / single-ended interface signal,
interface level 4.five-28Vdc compatible, no need external current limiting resistor
Output Signal  Alarm / in-position signal OC output, the output capacity is100mA, need external
pull-up resistor, the maximum pull up voltage is 24Vdc
Electronic Gear Ratio Default 4000 / rev, through the DIP switch or debug software setting subdivision
(200-51200)
Position Error Control Accuracy ±1 Pulse
Speed Control Accuracy  ±2 rpm
Maximum  Acceleration 100 rpm/ms

Dialing Swap Configurations

Pulse/Rev. SW1 SW2 SW3 SW4
Default ON ON ON ON
800 OFF ON ON ON
1600 ON OFF ON ON
3200 OFF OFF ON ON
6400 ON ON OFF ON
12800 OFF ON OFF ON
25600 ON OFF OFF ON
51200 OFF OFF OFF ON
1000 ON ON ON OFF
2000 OFF ON ON OFF
4000 ON OFF ON OFF
5000 OFF OFF ON OFF
8000 ON ON OFF OFF
10000 OFF ON OFF OFF
20000 ON OFF OFF OFF
40000 OFF OFF OFF OFF

Subdivision accuracy (electronic gear ratio) :When SW1, SW2, SW3, SW4 are ON, the generate uses the internal default micro-stage subdivision, the default inner subdivision of the driver is 400Pulse / rev, and the digital gear ratio can also be set by the debugging software. SW5 set the motor route,when turnON, the motor turns clockwise (CW),when change OFF, the motor turns counterclockwise(CCW). SW6 control mode choice, whenON, the motor enters the self-take a look at manner,generating 1 CZPT and reverse revolution, has been recurring till exit self-test manner, the exterior handle signal is invalid at self examination mode, whenOFF, the motor exits self-check manner,then the external handle signal is valid.

Mechanical Composition Dimension

 Driver mode Motor body length(mm) Driver thickness(mm) Integrated motor driver length(mm)
57IV90 seventy six thirty.2 106.two
57IV130  96 thirty.2 126.2
57IV180  116 thirty.two 149.2

Be aware : All previously mentioned is usually used, and we can customize according to your request or choose the suitable model for you, you should inform us following parameters: existing, voltage, holding torque, human body duration,the application area.

Software
Suitable for all sorts of modest and medium-sized automation equipments and instruments. Such as: laser products, health care products, 3D printer, tiny and medium-sized engraving machine, electronic processing gear, automated crawling gear, unique CNC machine resource, packaging products and robot. It is specially helpful for users who count on low noise and higher pace purposes.

Packaging and shipping
one.Outer packing: CZPT export carton with required delivery marks
two.Inner packing: Watertight packing with shock absorbing EPE and cardboard surrounded 
three.As for each the clientele demands

Our service
one.Working time : 8:00 a.m – ten:00 p.m .Any queries, please explain to us freely, we will be reply you asap.
2.Direct time : For samples, 2 to 5 days will be Alright. For mass production, the direct time count on the quantities you want.
3.Warrantity interval : eighteen months and Daily life-lengthy upkeep support for the solution.
4.We take products customize.

FAQ
Q1: How to select the suited stepper or servo motor?
A1: There are serveral critical items: measurement, size, holding torque, voltage, existing etc.After verify them and advised us, we can pick the appropriate one for you.

Q2: Any other strategies to finalize the model?
A2: Certain, you can ship us the product you are utilizing, we can help you locate the suited a single.

Q3:How to assure the Quality of CZPT Elements?
A3: We have the built-in program for industrial components quality handle. We have IQC (incoming quality control), IPQCS (in approach good quality control part), FQC (closing top quality control) and OQC (out-going quality management) to management each and every procedure of industrial components prodution.

This fall:What is actually the Advantage of Your Components for Business Merchandise? 
A4:one.The benefit of our items is the competitive charges, fast shipping and higher quality. Our
employees are responsible-oriented, pleasant-oriented,and diligent-oriented. Our goods are featured by strict tolerance, clean finish and prolonged services time.
2.Just before we send out the products,we check out them far more than a few moments.

Get in touch with

 

Integrated Low Heating Brushless Servo Motor with Driver Built-in